(Swedish)Independent thesis Basic level (university diploma), 15 credits / 22,5 HE creditsStudent thesis. Regelsamlingen för byggande innehåller Boverkets byggregler, BBR, med • Regelsamling för konstruktion – Boverkets konstruktionsregler, BKR, . Building permit. On most occasions, you need a building permit if you wish to build a new house, build an addition to your house or if you want.
|Published (Last):||23 August 2006|
|PDF File Size:||9.31 Mb|
|ePub File Size:||16.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
The form factor is increased in shadow zones. You can also find general information about accessibility, dwelling design, obligatory ventilation control and about the Swedish regulatory hierarchy.
Boverkets Konstruktionsregler BKR 94 design standards. Eurocode 2 provides a clearer definition of how much deflection can be allowed, it was not supplied in Boverkets structural design rules. Please use this url to cite or link to this publication: The results of these calculations are presented in Table 3.
The municipal building committee also has supervisory responsibility for the building works. The effect of wind load on the roof and wall cladding is determined by the form factor and the characteristic value of wind pressure qk. The load reduction factor Y is found in the following table.
Boverkets konstruktionsregler eks-10
All measurements are calculated based on the following documents and conditions Sweden: Later, in conjunction with the technical consultation and start-up statement, the building committee shall deal with the technical property requirements regarding dwelling design and other technical property requirements.
This thesis aims to show what impact this change from Boverkets structural design rules BKR to the Eurocode konstruktiionsregler have on the dimensioning of shear reinforcement and the calculation of deformation in concrete beams. Then find the value qk in the tables according to the type of terrain and the building height.
The tables of roof dimensions do not take wind load into account.
Go to the page menu Go to the page content. The value qk is determined based on the reference wind speed vref, the type of terrain, and the height of the building. The practical significance of this difference is very small; it only emerges in this thesis when the center distance between the shear reinforcements are determined in example tree. Compared to table 2.
The reason for the introduction of the Eurocode is to try and eliminate trade barriers between member states. When you build a building you need to follow the building code. If both the length and width of the building are twice as long as the height of the roof ridge, the fixing elements must be selected by taking into account the tensile load in proportion to the following form factor values.
The snow load on the roof is defined by the characteristic value skwhich is calculated as the product of the snow load reference value s0 and the form factor m.
The fact that the partial safety factor is not part of the Eurocode equations for determining the shear resistance in the same manner as it is in BKR, also contributes to the difference in the values. Boverket Boverket drafts mandatory provisions and general recommendations in Boverket’s Building Regulations.
Login LT EN e.
In order to demonstrate the differences in structural design, with respect to shear force, three examples are calculated. Roof without thermal insulation. Form factor m is used for selecting the fixing elements of roofing and determining their dimensions.
Swedish Regulations for building works
The building code in Sweden contains mandatory provisions and general recommendations. The bboverkets building committee shall, among other things, assess whether the design requirements are fulfilled.
To examine differences between the calculations of deformation, one method from BKR and one from Eurocode 2 is used. The biggest change to the rules for structural shear design is the requirement for minimum shear reinforcement in concrete beams.
Form factor maximum values are specified below in roof schemes according to the roof slope. This reinforcement should be installed along the entire beam, whether it is needed to achieve sufficient strength or not. The regulations you need to know and follow depend on what you want to build or alter.
Swedish Regulations for building works – Boverket – Boverket
Roof with thermal insulation. Boverket publishes the Swedish building code. Each example is calculated in accordance with kojstruktionsregler different methods, two taken from BKR and one from Eurocode 2. The distance is larger according to Eurocode compared to BKR.
The municipal building committee The municipal building committee shall, among other things, assess whether the design requirements are fulfilled. Wind load pull — self-weight.
The results in Table 2. This is explained by the differences in how the creep rate is determined in the different methods. The snow load reference value depends on the location of the building. Wind load on walls. Taking into account the requirement of minimum reinforcement, table 2.
It is assumed that the length and width of the building are twice as konsrruktionsregler as the height to the ridge of the roof. The relationship between the snow load form factor and roof structure is presented below.
The information presented is suitable for single and double pitched roofs. The value of the wind speed vref is selected based on the location of the building. The form factor m depends on wind direction and the form of the building as presented in the table below and on the next page.
The form factor boverketa is used for calculating the dimensions of the cladding.