Buy KDS Daishinku/KDS DSXGM only $ at EasyEDA components online store LCSC. Crystals|SMD Crystals datasheet, inventory and pricing. Type. DSXG. Frequency・Range. ・to・9MHz 9・to・MHz ・to・11MHz 11・to・12MHz 12・to・20MHz 20・to・27MHz 27・to・64MHz. Overtone・Order. Cheap package dhl, Buy Quality crystal boutonniere directly from China crystal baking Suppliers: KDS DSXG series SMD Crystal 48MHZ 48M Resonator.
|Country:||Turks & Caicos Islands|
|Published (Last):||17 February 2008|
|PDF File Size:||1.96 Mb|
|ePub File Size:||17.35 Mb|
|Price:||Free* [*Free Regsitration Required]|
Be sure to have a mounting test in advance by using the actual ods machine and check that the characteristics of the products are not damaged by the automatic mounting.
M Plating material of a terminal.
KDS Daishinku/KDS DSXGM – PDF Datasheet – SMD Crystals In Stock |
The tip of cover-tape shall be fixed temporary by paper tape and roll around the core of reel one round. Underfilling Material for DSXG Types,KDS considers underfilling material such as heat-cured resin would not affect the characteristics of the DSXG crystal mounted, however, we recommend the crystal be tested and checked in such a case prior to use so that there are the possibility that the crystal may have a cap off or a crack in the ceramic base.
Although the check about ultrasonic washing is performed, since it is an examination with a simple substance, the check for the second time by the use state is recommended. Please use it below with the value specified on a catalog and specifications. The empty embossed area which are sealed by cover-tape must remain more than 40mm. C and no abnormality shall be observed in external appearance and sealing tightness and others shall be based on ET of EIAJ.
DSXG 32MHz from KDS Daishinku
In the upper and lower part and the opening in box it shall be protected products using aircushion sheets. Since mounting by Ultrasonic welding and processing have a possibility of an excessive vibration spreading inside a crystal resonator and becoming the cause of characteristic deterioration and ddx321g oscillating, it does not recommend.
Sine waves of 1. Also, no serial bubble is observed by Fluorocarbon tests. Please refrain from forming csx321g between crystal land pattern’s since there is a possibility to cause crack in base.
【DSX321G KDS】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA
Mount the specimen on substrate. C perform the attached Reflow conditions to dsx321v. C Transport Time min ? C and no abnormal appearance shall be observed. Please keep it in the place which direct rays do not hit and dew condensation does not generate. In the process where the boad is warped, such as board separation process, be careful that the warping does not influence the characteristics and soldering of crystal products.
However when too much shock is added according to a certain cause, the use after a characteristic check is recommended. C 30min 1 cycle Avoid using the product at temperature higher than specified.
Glass Epoxy 1 cycle: Apply the following pressure Weight: C and no abnormality shall be observed in external appearance and sealing tightnen and others shall be based on ET of EIAJ. Reflow soldering shall be allowed only 3 times.
It is a guaranteed term because it obtains an excellent soldering: Further,parts shall be solderd on substrate, fixed Aluminum materials about g.
KDS DSX321G 12M 12MHZ 12.000MHZ 3225 crystal passive patch 4Pin
C 3cycles 18times drop from cm heights to concrete. After all products were packaged, must remain more than twenty pieces or mm empty area, which should be sealed by cover-tape. However please consult in advance about other washing liquid. A clearance between the soldering terminal portion and a print circuit board side should be less than 0. C 10 s s 60 s Total time: